Paper Diffraction Grating Glasses: We’re with the squad back at New York’s hottest cyberpunk club, Near Field Commune(ication), and it’s still got everything, Adabot & the Circuit Playground, Collin’s wondrous, mind-blowing, heart-stirring Pulse Room, and more! And you are dressed to the cyber-nine’s, with wearable LEDs, EL tape, a full set of glittering RFID/NFC Nail Stickers, and finishing off your ensemble with a pair of Diffraction Glasses.
Anti-Static ESD Rework Mat with Grounding Clip – A4 Size – 20cm x 30cm: This anti-static work mat is great for electronic work and repair, especially delicate or ESD sensitive work. It’s 2mm thick and has a very high-resistance covering, like 10’s of Megaohms. There’s a clip attached that you need to connect to an earth ground in order to ground the mat. Usually, folks connect it to a known-grounded metal chassis.
Sony Spresense Main Board – CXD5602: Here’s a compact development board based on Sony’s power-efficient multicore microcontroller CXD5602. It allows developers to create applications in a very short time and is supported by the Arduino IDE as well as the more advanced NuttX based SDK.
Sony Spresense Pack – Main Board + Extension Board + Camera: SPRESENSE is a low-power board computer for the IoT that is equipped with a GPS receiver and supports High-Resolution Audio codecs. The board allows for IoT versatility and can be developed for a vast range of uses, such as a drone utilizing the GPS and high-performance processor, a smart speaker utilizing High-Resolution Audio recording and playback as well as the built-in full-digital amplifier, or a low-power time-lapse camera utilizing the camera interface. SPRESENSE will make the IoT smarter and more efficient.
Instead of hemming and hawing which IoT boards to pick for your project, we’re offering an easy all-in-one pack!
Sony Spresense Extension Board: Spresense is a compact development board based on Sony’s power-efficient multicore microcontroller CXD5602. It allows developers to create IoT applications in a very short time and is supported by the Arduino IDE as well as the more advanced NuttX based SDK. The Spresense Extension Board has connectors in addition to Arduino Uno compatible pin sockets
Sony Spresense 5MP Camera Board: The latest addition to Spresense’s hardware ecosystem is the Spresense Camera Board that connects directly to the main board’s camera interface.
The Spresense camera board has the Sony ISX012 image sensor mounted with a lens. The Sony ISX012 has an effective pixel count of 5.11M pixels and an onboard encoder that can acquire pictures in JPEG, RAW, Y/C or RGB format.
Assembled Adafruit Feather M0 WiFi – ATSAMD21 + ATWINC1500: Feather is the new development board from Adafruit, and like its namesake, it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores. This is the Assembled Adafruit Feather M0 WiFi w/ATWINC1500 – our take on an ‘all-in-one’ Arduino-compatible + high speed, reliable WiFi with built in USB and battery charging. Its an Adafruit Feather M0 with a WiFi module, ready to rock! We have other boards in the Feather family, check’em out here.
Circuit Playground Bluefruit – Bluetooth Low Energy: Circuit Playground Bluefruit is our third board in the Circuit Playground series, another step towards a perfect introduction to electronics and programming. We’ve taken the popular Circuit Playground Express and made it even better! Now the main chip is an nRF52840 microcontroller which is not only more powerful, but also comes with Bluetooth Low Energy support for wireless connectivity.
Adafruit LPS33HW Water Resistant Pressure Sensor – STEMMA QT: Sometimes you need to sense pressure in a damp or caustic environment. And sometimes you need to know the relative changes in pressure as well as the absolute pressure. For the times you need to do both (or either), the LPS33HW is the pressure sensor for you. Combining protection from water intrusion with support for high precision relative and absolute measurements, this sensor will do what you need. With drivers for CircuitPython, Arduino, and Raspberry Pi, and support for I2C or SPI (Arduino only SPI support, for now) you’ll be measuring pressure in any situation in no time.