New Products 5/22/19 Featuring Adafruit PyGamer! #adafruit




from New Products 5/22/19 Featuring Adafruit PyGamer! #adafruit
by Kelly

Screen Shot 2018 05 04 at 7 44 26 AM

We’ve got the New nEw NEW for you right here:


NEW PRODUCTS THIS WEEK


4182 02

3.5mm Mono Audio Jack to Alligator Clip Cable

This cable is easy to understand – you get a 3.5mm mono audio jack on one end, and two alligator clips on the other. It’s also really easy to use, perfect for clipping onto a micro:bit or Circuit Playground! It’s also good for use with AT (accessibility technology) buttons as they use 3.5mm mono cables for interconnection.

Read more


4181 02

3.5mm Mono Audio Plug to Alligator Clips

This cable is easy to understand – you get a 3.5mm mono audio plug on one end, and two alligator clips on the other. It’s also really easy to use, perfect for clipping onto a micro:bit or Circuit Playground! It’s also good for use with AT (accessibility technology) buttons as they use 3.5mm mono cables for interconnection.

Read more


4198 01

USB C to USB C Cable – USB 3.1 Gen 4 with E-Mark – 6″ long

As technology changes and adapts, so does Adafruit! Rather than the regular USB A, this cable has USB C to USB C plugs!

Read more


4199 01

USB C to USB C Cable – USB 3.1 Gen 4 with E-Mark – 1 meter long

This cable is a little more expensive than most USB cables because it has all the data pins connected, so it can be used for any USB C device, with any power or speed requirements. The internal wires are 32 AWG. It also includes an EMARK chip, required by the USB C specification but sometimes left out. That means you can use this for high current (5A) charging.

Read more


4232 10

Multifunctional USB Digital Tester – USB A and C

This handy (pun intended?) tool can measure voltage, current, power, charge time, and other measurements for USB A, Micro B, and USB C! It features a colorful display that pops up when you plug in a power supply. Each click of the button gives you a different display and readout. A long press will reset the data for when it does Coulomb-counting (total power consumption). We like the simple display that comes up first with big Voltage and Current output, but you have lots of options.

Read more


4249 04

Heat-Set Insert For Soldering Irons – M5 Inserts

Wanna improve the connection strength between your project’s 3D-printed parts, and also have nice clean surfaces? Instead of gluing bits together, or screwing plastic screws directly into your 3D prints, use strong and reusable machine screws and heat-set inserts. Heat set inserts are only a few cents a piece and have a grooved outside, with theads on the inside. Originally they were designed for injection molded parts but they work fabulously for 3D printed plastic as well.

Read more


4239 06

Heat-Set Insert For Soldering Irons – #4-40 / M3 Inserts

Wanna improve the connection strength between your project’s 3D-printed parts, and also have nice clean surfaces? Instead of gluing bits together, or screwing plastic screws directly into your 3D prints, use strong and reusable machine screws and heat-set inserts. Heat set inserts are only a few cents a piece and have a grooved outside, with theads on the inside. Originally they were designed for injection molded parts but they work fabulously for 3D printed plastic as well.

Read more


4208 02

JST SH 4-pin Right Angle Connector (10-pack) – Qwiic Compatible

If you’re a DIY enthusiast who likes to micro-manage your project’s connections, here is a 10-pack of some micro JST SH connectors! They’re solid plastic with 4 x 1mm pitch through-hole mounting tabs. In an SMT line you can just paste over the through holes and the pads will solder in place.

Read more


4177 03

M5Stack Gray Development Kit – ESP32 Dev Board w/ MPU9250

Get yourself a kit that can do it all! The M5Stack Gray Development Kit is a ESP32-based WiFi microcontroller that’s compatible with MicroPython and Arduino. It comes jam-packed with Wi-Fi / Bluetooth capability, running at 240 MHz with the dual-core processor and 4MB of SPI Flash.

Read more


4178 08

M5Stack Basic Core IoT Development Kit – ESP32 Dev Board

Get yourself a kit that can do it all! The M5Stack Basic Development Kit is a ESP32-based WiFi microcontroller that’s compatible with MicroPython and Arduino. It comes jam-packed with Wi-Fi / Bluetooth capability, running at 240 MHz with the dual-core processor and 4MB of SPI Flash.

Read more


4176 04

M5Stack FACES ESP32 Pocket Computer – Keyboard, Game, Calculator

Get yourself a kit that can do it all! The M5Stack FACES Pocket Computer is a ESP32-based 3-in-1 pack with swappable keyboard / Gaming / calculator panels! Each panel can be upgraded through downloading firmware updates.

Read more


4228 00

Plastic Button Caps For Square Top (10-pack) – 8mm Diameter

These Reese’s Piece’s lookin’ bits fit perfectly on top of tactile buttons with 2.4mm square tops and give a satisfying 8mm diameter surface area for your fingers to press.

Read more


4238 00

Adafruit PyGamer Acrylic Enclosure Kit

You’ve got your PyGamer, and you’re ready to start jammin’ on your favorite arcade games. You gaze adoringly at the charming silkscreen designed by Ada-friend PaintYourDragon. The nostalgia is palpable!

Read more


4242 00

Adafruit PyGamer for MakeCode Arcade, CircuitPython or Arduino

What fits in your pocket, is fully Open Source, and can run CircuitPython, MakeCode Arcade or Arduino games you write yourself? That’s right, it’s the Adafruit PyGamer! We wanted to make an entry-level gaming handheld for DIY gaming, and maybe a little retro-emulation. It’s not the fastest and best of everything but it is an all-in-one dev board with a lot of possibilities!

Read more


New Products 5/22/19 Featuring Adafruit PyGamer

Visit www.adafruit.com/new for more info.





Original article: New Products 5/22/19 Featuring Adafruit PyGamer! #adafruit
Author: